I recently stumbled upon a really fantastic Reddit post by user synapticsynapsid about how to build your own book and decided that I couldn’t keep this great little tidbit to myself. I’ve always loved the idea of printing and binding my own books (especially if it’s for a book that I don’t want anyone else to read – I think we’ve all got at least one of those), so when I found this great visual guide, I immediately bookmarked it (and then promptly forgot about it for two years). Now, I unfortunately haven’t tried to do it yet. But it’s definitely a project that I’d like to eventually take on! Maybe in the future I’ll make my adventure into bookbinding into its own little blog post…
Anyway, for now, here’s synapticsynapsid‘s guide on how to build your own book:
The dimensions of the paper don’t matter. Just make sure that the fibers of the paper are ALWAYS facing upwards just like a book standing in your bookcase. (In this case, the fibers are aligned along the short side of the paper)
Fold all pages once. (You can feel the fibers by the way the paper bends when you fold it. If it feels flexible then that is the way the fibers are aligned).
Put them in each other 4 by 4. Let’s call this a “flap” for now.
Stack all the flaps together and put in under pressure. Preferably for 24 hours.
Mark the flaps with a pencil, the lines should be equal apart in length. The space in between the two closest lines here is 1cm. The size may differ depending on the dimension of the books.
Poke holes in the marks with a sewing needle. This is easier to do if you have a lamp in front of you. (This is why we made them 4 by 4. More papers will make it too thick and harder to pierce).
Take a thread the length of your total amount of flaps (plus a little more for good measures) and drag the thread against wax. This will prevent the thread from breaking. I’m using a beeswax candle.
Enter the first hole of the flap, go through and exit the next hole and repeat.
It should look like this.
Place a new flap on top of the old one and enter the hole directly above.
Add bands or some sort and place them in the smallest “grids”. We do this to add sturdiness to the back. I’m using the fibers of a coarse linen thread.
Always tug the thread after finishing each flap.
After the third flap you must make a small knot in the flap right below your newly finished one.
Enter the next and make sure to always tie it at the ends.
It should look something like this inside the pages.
Stitch by stitch, stitching it together.
Done. Finish it with a double knot.
Put a thin layer of glue on the back. Remove the excess glue with your fingers and put the pages under pressure for another 24 hours.
Wet a thin piece of cloth (or special paper) with glue and attach to the back
Cut 2 pieces from hard cardboard to use as covers for the book. They should be just a few millimeters broader than the pages, we want a margin here. Again, it is extremely important that the fibers are facing upwards just like the pages. You can feel the fibers by bending the cardboard.
Cut out a small piece of thin carton paper. The size of it should be the exact dimensions as the backside of your book pages. Glue it against a piece of paper.
Optional! Add fancy bands for decoration.
Now glue the hard cardboard covers on the paper back, the thin carton paper piece should be face down. The margin between covers and carton back should be about half a centimeter, give or take.
Cut out a piece of cloth that you fancy for the covers. Make it larger than the covers by a few centimeters. (If the cloth is so thin that you can see through it in the light then you might want to take a thin piece of paper and glue it against the cloth for thickness).
Add glue to the cloth and cut away the edges around the cover in a 45 degree angle. Cut away some near the backside too. Place the cover on the cloth and fold all the edges over the cover to make it stick.
Place the pages inside the cover and carefully add a thin layer of glue at the back of the very last page.
Use force and press all over it to make sure it sticks everywhere.
Repeat on the other side.
Put the book under pressure for another 24 hours.
The finished product!
In the comments section of the posting, a friendly bookmaker that goes by the name of mist_of_silver popped in to give a few excellent tips:
“When you cut the 45 degree corners, make sure to leave a little extra. as you can see in the last picture, if you cut it too close, it will leave the corners of the cardboard exposed. It makes a much better finished product if you leave extra so that the corners will the completely hidden.
Also, paper can be finicky. When it gets wet, it curls and stretches. Most the time it’s not a huge deal, but when gluing down the first and last page to the cover, it will stretch and sometimes stretches so much it is visible out beyond the edge of the cover. To prevent this, you can trim a tiny bit off before you glue it.
Also for the reason that paper likes to curl, I would put a piece of waste paper down underneath the pages you are gluing out. This way if it curls, the glue will get on the waste paper instead of your nice clean text block. Also, put a piece of wax paper in between the glued page and the first page of your book while you have it under weight – glue will often seep through the paper and stick to the other paper, making it difficult to open properly. Wax paper won’t stick.”
For more discussion on this guide to bookmaking (and more tips!), I highly recommend checking out the actual Reddit thread by clicking right here!
Let me know in the comments if you decide to take on this fun bit of crafting! I’d love to see your finished product.
Special thanks to synapticsynapsid for the great guide!